Using the system
Initialization
When the ignition switch is pushed to the ON position, INFINITI Voice Recognition is initialized, which may take up to one minute. When completed, the system is ready to accept voice commands. If the TALK switch is pushed before the initialization completes the display will show the message: “System not ready.” or a beep sounds.
Before starting
To get the best performance from INFINITI
Voice Recognition, observe the following.
► Keep the interior of the vehicle as quiet
as possible. Close the windows to
eliminate the surrounding noises (traffic
noises, vibration sounds, etc.),
which may prevent the system from
recognizing the voice commands correctly.
► When the air conditioner is in the
“AUTO” mode, the fan speed decreases
automatically for easy recognition.
► Wait until a tone sounds before speaking
a command.
► Speak in a natural voice without pausing
between words.
Giving voice command
1. Push and release the TALK switch located on the steering wheel.
2. A list of commands appears on the screen, and the system announces, “Please say a command”. 3. After the tone sounds and the icon on the screen changes from , speak a command.
Operating tips:
► Voice commands cannot be accepted
when the icon is .
► The list displayed can be scrolled by
tilting the menu control switch on the
steering wheel.
► If the command is not recognized, the
system announces, “Please say again”.
Repeat the command in a clear voice.
► Push the BACK button once to return to
the previous screen.
► If you want to cancel the command,
push and hold the TALK switch for
1 second. The message “Voice canceled”
will be announced.
► To skip the voice guidance function and
give the command immediately, push
the TALK switch to interrupt the
system. Remember to speak after the
tone.
► If you want to adjust the volume of the
system feedback, push the volume
control switch (+ or −) on the steering
wheel or use the audio system volume
knob while the system is making an
announcement.
How to speak numbers:
INFINITI Voice Recognition requires a certain way to speak numbers when giving voice commands. Refer to the following examples.
General rule
Only single digits 0 (zero) to 9 can be used. (For example, if you would like to say 500, “five zero zero” can be used, but “five hundred” cannot.
Phone numbers
Speak phone numbers according to the following examples:
► 1-800-662-6200
— “Dial one eight zero zero six six two six two zero zero.” Note 1: For the best voice recognition phone dialing results, say phone numbers as single digits. Note 2: You cannot say 555-6000 as “five five five six thousands”. Note 3: When speaking a house number, speak the number “0” as “zero”. If the letter “o (Oh)” is included in the house number, it will not be recognized as the number “0 (zero)” even if you speak “oh” instead of “zero”. Please speak “zero” for the number “0 (zero)”, “oh” for the letter “o (oh)”.
Send digits using dial tone:
► Press the TALK switch during a
phone call.
► The menu will be launched and you will
be provided with the following guidance:
"Please say the digits to dial".
► After guidance, say the digits of the
number you want to send. After this,
the digits that have been recognized
will be read out.
► If you press the ENTER button on the
steering wheel or on the INFINITI controller,
the selected digits will be sent.
Speaker adaptation function (for Alternate Command Mode)
The voice recognition system has a function to learn the user’s voice for better voice recognition performance. The system can memorize the voices of up to three persons.
Having the system learn the user’s voice:
1. Push the SETTING button on the instrument panel and select the “Others” key. 2. Select the “Voice Recognition” key. 3. Select the “Speaker Adaptation” key.
4. Select the user whose voice is memorized by the system. 5. Select the “Start Speaker Adaptation Learning” key.
6. Select a category to be learned by the system from the following list.
► Phone Commands
► Navigation Commands
► Information Commands
► Audio Commands
► Help Commands
The voice commands in the category are displayed. 7. Select a voice command and then push the ENTER button. The voice recognition system starts.
8. The system requests that you repeat a command after a tone. 9. After the tone sounds and the icon on the screen changes from , speak the command that the system requested. 10.When the system has recognized the voice command, the voice of the user is learned. Push the switch or BACK button to return to the previous screen. If the system has learned the command correctly, the voice command status on the right side of the command turns from “None” to “Stored”.
Speaker Adaptation function settings:
Edit User Name
Edit the user name using the keypad displayed on the screen.
Delete Voice Data
Resets the user’s voice that the voice recognition system has learned.
Continuous Learning
When this item is turned to ON, you can have the system learn the voice commands in succession, without selecting commands one by one.
Minimize voice feedback (for Alternate Command Mode)
To minimize the voice feedback from the system, perform the following steps. 1. Push the SETTING button on the instrument panel. 2. Select the “Others” key. 3. Select the “Voice Recognition” key. 4. Select the “Minimize Voice Feedback” key. 5. The setting is turned to ON and the voice guidance will now be reduced when using the Voice Recognition system.
See also:
DISC·AUX but
Park the vehicle in a safe location for the front seat occupants to operate the DVD player while watching the images.
Insert a DVD into the CD/DVD slot with the labeled side up. The DVD will be guide ...
Underbody
In areas where road salt is used in winter,
the underbody must be cleaned regularly.
This will prevent dirt and salt from building
up and causing the acceleration of corrosion
on the underbody ...
How to adjust the screen view
To adjust the Display ON/OFF, Brightness, Tint, Color, Contrast and Black Level of the Around View Monitor, press the SETTING button with the Around View Monitor on, select the item key and adjust the ...